INSIGHTS

What Is Alu-Alu Blister Packaging? Alu-Alu vs PVC and PVC/PVDC

What Is Alu-Alu Blister Packaging? Alu-Alu vs PVC and PVC/PVDC

Tablets in aluminium blister packs


Most tablets and capsules are sold in blister packs. A blister has two parts: the formed base with cavities that hold the product, and the lidding foil that seals them. What sets blister types apart is the material of the base and how it is formed, and that choice determines how well the medicine is protected from moisture, oxygen and light.

Thermoformed blisters: PVC and PVC/PVDC

In a classic clear blister, the base is a plastic film that is heated and formed into cavities (thermoforming).

  • Mono PVC film: a single-layer clear PVC film. Svamazon’s mono PVC films are 200–500 microns thick.

  • Duplex PVC/PVDC: PVC film coated with PVDC, which improves the moisture and gas barrier. The coating weight is expressed in grams per square metre (gsm); Svamazon’s PVC/PVDC films carry 40–120 gsm of PVDC.

  • Triplex PVC/PE/PVDC: a multilayer structure with a PE layer between the PVC and the PVDC, used for moisture-sensitive tablets and capsules.

The main advantage of a thermoformed blister is transparency: the tablet is visible. Its barrier is limited by the film structure.

Cold form (Alu-Alu) blisters

An Alu-Alu blister, as the name suggests, has aluminium in both the base and the lid. The base is a multilayer laminate containing aluminium, formed by pressing with a die without heat, which is why it is also called cold form foil.

  • The standard structure of Svam Toyal’s Alublis® cold form foil is BOPA 25 µm / aluminium 45, 50 or 60 µm / PVC 60 µm; a 4-layer PVC/BOPA/aluminium/PVC structure is also available.

  • Svamazon’s Alu-Alu foils come as 3-ply (OPA/aluminium/PVC), 4-ply (PVC/OPA/aluminium/PVC) and printed versions.

  • According to Svam Toyal, cold form laminate was developed for ultimate high-barrier protection against moisture, oxygen and light.

Alu-Alu blisters are opaque, so the tablet is not visible. They are chosen for products with demanding barrier needs.

Tropical blisters: in between

A tropical blister adds a second aluminium layer over a clear thermoformed blister. Svam Toyal describes its tropical foil as a “shield” over the plastic packaging, made of OPA, aluminium foil and heat-seal lacquer, protecting against moisture, oxygen, light and UV.

Lidding foil

Whatever base is used, the cavities are sealed with lidding foil. Svam Toyal’s lidding foils are primer-coated, hard-tempered aluminium with a heat-seal lacquer (HSL), 20–30 microns thick with 3–10 gsm HSL, plain or printed, and suitable for PVC, PVDC, cold form and tropical forming films.

Desiccant cold form foil

For some products, keeping moisture out is not enough; moisture inside the cavity also needs to be absorbed. In Svam Toyal’s DRYBLIS® foil, the desiccant layer is built into the foil itself. Details on our DRYBLIS® product page.

Which blister, when?

Blister

Properties

PVC

Appearance: clear
Forming: heat (thermoforming)
Barrier: basic

PVC/PVDC (duplex, triplex)

Appearance: clear
Forming: heat (thermoforming)
Barrier: increases with PVDC weight

Tropical

Appearance: opaque outer layer
Forming: thermoforming + aluminium shield
Barrier: moisture, oxygen, light and UV protection

Alu-Alu (cold form)

Appearance: opaque
Forming: cold forming
Barrier: highest against moisture, oxygen and light

The choice depends on the drug’s sensitivity to moisture, oxygen and light, the climatic zone where it will be sold, its shelf life and the results of stability studies. A change of packaging usually also requires an update to the marketing authorisation dossier.

Note: This article is for general information. The final choice should rest on your product’s stability data.

Blister materials with Vinder

Vinder is the distributor and representative of Svam Toyal and Svamazon in Türkiye. See our pages on cold form (Alu-Alu) foil, DRYBLIS®, blister lidding foil, tropical blister foil, Alu-Alu foil, mono PVC film and PVC/PVDC film.

Frequently asked questions

What does Alu-Alu blister mean?

A blister whose base and lid are both aluminium. The base is formed by pressing an aluminium laminate without heat (cold forming).

What is PVC/PVDC?

PVC film coated with PVDC, which improves the film’s moisture and gas barrier. The coating weight is expressed in gsm.

What is the difference between mono, duplex and triplex?

Mono is a single-layer PVC film, duplex is PVC/PVDC and triplex is PVC/PE/PVDC.

Is a tropical blister the same as an Alu-Alu blister?

No. In a tropical blister, the base is a clear thermoformed film with an aluminium shield added over it; in an Alu-Alu blister, the base itself is an aluminium laminate.

Sources

Contact Us